Caldigit RAID Card Manual do Utilizador

Getting Started

10 A. MacPro1.6 Remove PCI-Express card(s)Disconnect and remove all PCI-Express card(s) except for your graphics card, lift the latch on the card con

11A. MacProCPU CoverPull from here.Fan module(b) (8 Core Mac Pro) Remove the CPU cover by pulling the bottom edge of the CPU cover slightly toward y

12 A. MacPro1.9 Remove the system drive Remove the system drive from MacPro hard disk drive carrier. FixedCalDigit optical bay tray (as shown below

13A. MacPro1.11 Install CalDigit optical bay tray Install CalDigit optical bay tray with the system drive into the 2nd optical drive and xed .1.12

14 A. MacPro1.14 Connect SATA connector to the SATA port Connect SATA connector to the SATA port on the mother board, and make sure It's fully

15A. MacPro1.17 Replace the optical bay1.18 Disconnect the iPass cable Disconnect the iPass cable from the upper left corner of the main logic board

16 A. MacPro1.19 Connect the iPass connector to CalDigit RAID Card (Make sure the iPass connector is securely connected to CalDigit RAiD Card's

17A. MacPro Note: It maybe necessary for you to disentangle the iPass cablefrom other cables running through the same area so that the looseend of th

18 A. MacPro1.21 Installing the fan moduleIf you are using a Power Mac G5, please skip to step 1.24. Install the fan module back insdie the chassis.

19A. MacProCPU Cover(b) (8 Core MacPro) Position the bottom front edge of the cover and then rotate the top back until the magnets snap it into pla

2Apple, Apple Logo, Mac, the Mac logo, FinalCut Pro, Macintosh, are trademarks of Apple Computer Inc. Microsoft, Windows and Windows Logos are registe

20 A. MacPro1.24 Install the PCI bracket and tighten the thumb screws 1.25 Slide the memory cards back into the DIMM cage (4 Core Mac Pro) 1.26 M

21A. MacPro1.27 Insert the side panel and close the latchReconnect the external cables and the power cord. Turn on the power of your Mac.Note: To ins

22 A. MacPro1(b) If you are using the rst internal hard drive as the system drive (including the use of Boot Camp), and the other three drives for th

23A. MacPro1.2 Turn O󰮏/ Shut Down your computer Turn o󰮏 your computer. Touch the metal on the outside of your MacPro (chassis) while it's still

24 A. MacPro1.4 Remove the drive modules Make sure the latch on the back panel is open, and pull out all four drive modules as well as their empty ca

25A. MacPro1.6 Remove PCI-Express card(s) Disconnect and remove all PCI-Express card(s) except for your graphics card, lift the latch on the card con

26 A. MacPro(b) (8 Core MacPro) Remove the CPI cover by pulling the bottom edge of the CPI cover slightly toward you.1.8 Remove the fan module (a)

27A. MacPro1.9 Disconnect the iPass cable Disconnect the iPass cable from the upper left corner of the main logic board and extend toward the PCI con

28 A. MacProConnector on cardiPass cable1.10 Connect the iPass connector to CalDigit RAID CardMake sure the iPass connector is securely connected to

29A. MacPro Note: It maybe necessary for you to disentangle the iPass cablefrom other cables running through the same area so that the looseend of th

3Installing the CalDigit RAID CardFollow the instructions on the following pages to install the CalDigit RAID card in your Mac Pro, PCI-e PowerMac G5

30 A. MacPro1.12 Installing the fan moduleIf you are using a Power Mac G5, please skip to step 2.15. Install the fan module back insdie the chassis.

31A. MacProCPU Cover(b) (8 Core MacPro) Position the bottom front edge of the cover and then rotate the top back until the magnets snap it into pla

32 A. MacProPCI bracket1.15 Install the PCI bracket and tighten the thumb screws 1.16 Slide the memory cards back into the DIMM cage (4 Core Mac Pr

33A. MacPro1.18 Insert the side panel and close the latchReconnect the external cables and the power cord. Turn on the power of your Mac.Note: To ins

34 A. MacPro1(c) If you are using a MacPro to make four internal hard drives into a RAID volume, and install the operating system onto the RAID volume

35A. MacPro1.2 Turn O󰮏/ Shut Down your computer Turn o󰮏 your computer. Touch the metal on the outside of your MacPro (chassis) while it's still

36 A. MacProPort access coverPCI bracketLatch1.4 Remove the drive modules Make sure the latch on the back panel is open, and pull out all four drive

37A. MacPro1.6 Remove PCI-Express card(s) Disconnect and remove all PCI-Express card(s) except for your graphics card, lift the latch on the card con

38 A. MacPro(b) (8 Core MacPro) Remove the CPI cover by pulling the bottom edge of the CPI cover slightly toward you.1.8 Remove the fan module (a)

39A. MacProiPass cable1.9 Disconnect the iPass cable Disconnect the iPass cable from the upper left corner of the main logic board and extend toward

4Working Safely Inside the Mac Pro. Make sure to discharge any potential static electricity before you touch anycomponents inside. To do this, simply

40 A. MacPro1.10 Connect the iPass connector to CalDigit RAID CardMake sure the iPass connector is securely connected to CalDigit RAiD Card's J1

41A. MacPro Note: It maybe necessary for you to disentangle the iPass cablefrom other cables running through the same area so that the looseend of th

42 A. MacProFan module1.12 Installing the fan moduleIf you are using a Power Mac G5, please skip to step 3.15. Install the fan module back insdie the

43A. MacProCPU Cover(b) (8 Core MacPro) Position the bottom front edge of the cover and then rotate the top back until the magnets snap it into pla

44 A. MacPro1.15 Install the PCI bracket and tighten the thumb screws1.16 Slide the memory cards back into the DIMM cage (4 Core Mac Pro) 1.17 Mak

45A. MacPro1.18 Install the system drive from MacPro into USB or Firewire 外接盒, and then connect to your computer.1.19 Insert the side panel and c

46 A. MacPro1.20 Open RAID Shield, to add a new Controller.1.21 To set up a RAID volume based on the RAID Level you need

47A. MacPro1.22 After conguring your RAID, please launch Apple's Disk Utility ( application / utility / Disk utility ) to restore your Mac OS

48 B. PCI-e G52 If you are using a PCI-e G52.1 Install the CalDigit Driver v1.8.0 (a) Go to http://www.CalDigit.com/Support/HDPro-HDOne-RAIDCard-1.8

49B. PCI-e G52.2 Turn O󰮏/ Shut Down your computer Turn o󰮏 your computer. Touch the metal on the outside of your MacPro (chassis) while it's stil

5About the Installation of the CalDigit RAID CardThe installation instructions provide the following congurations:1. If you are using a Mac Pro(a) To

50 B. PCI-e G52.4 Loosen the screws and remove the bracket and the port access cover of PCI Express slot 4 by using the provided toolMake sure the

51B. PCI-e G52.6 Insert the side panel and close the latch Reconnect the external cables and the power cord. Turn on the power of your PCI-e G5.Note:

52 C. Wintel PC3 If you are using a Wintel PC3.1 Download CalDigit Windows or Linux Driver Go to http://www.CalDigit.com/Support/

53C. Wintel PC3.2 Turn O󰮏/ Shut Down your computer Turn o󰮏 your computer. Touch the metal on the outside of your MacPro (chassis) while it's sti

54 C. Wintel PC3.4 Loosen the screws and remove the bracket and the port access cover of PCI Express x4 and above3.5 Slide the CalDigit RAID Card

55C. Wintel PC3.6 Install PCI-Express screws back in place. 3.7 Insert the side panel and close the latch Reconnect the external cables and the powe

56 C. Wintel PC3.8 Follow your Operating System to select CalDigit Windows or Linux driver 3.9 Install RAID Shield from our website. www.CalDig

57After installing the CalDigit RAID Card drivers and RAID Shield, you will be able to use RAID Shield to set up your RAID and congure your RAID leve

58(*1)Part # CBMiniSAS-BC SKU# 702101 (for Boot Camp)(*2)Part # CBMiniSAS-4C SKU# 702102 (for PC)(*3)Part # CRCCBBM SKU# 760400*Optional

CalDigit RAID Card Getting Started Manual v1.5www.caldigit.com ©Copyright 2008 CalDigit, Inc. All Rights Reserved

6 A. MacProInstalling your RAIDPlease follow the following steps to install your CalDigit RAID Card.

7A. MacPro1(a) If you are using a MacPro with one hard drive as the system drive and four internal hard drives as the RAID volume1.1 Install the Cal

8 A. MacPro1.2 Turn O󰮏 / Shut Down your computer Turn o󰮏 your computer. Touch the metal on the outside of your Mac Pro (chassis) while it’s still plu

9A. MacPro1.4 Remove the drive modulesMake sure the latch on the back panel is open, and pull out all four drive modules as well as their empty carri